Saab 9-5

since 1997 of release

Repair and car operation

Removal, installation, dismantling and assembly of a forward door and its components

Below the driver's door is considered; removal and installation of the right door is made similarly.

Removal, installation and door adjustment

PERFORMANCE ORDER

Separate the socket (1) electroconducting of a door and remove from A rack the limiter (2) courses of a door.

Give at first the bottom nut (3) bottom loops, and then, holding a door, a nut (4) top loops.

Remove a door from loops.

Installation is made upside-down. After installation adjust the provision of a door concerning a body.

For adjustment of provision of a door in the longitudinal plane of the car at door removals slightly turn out bolts of fastening of loops to a body, establish a door and adjust its situation. Then remove a door and tighten bolts of fastening of loops to a body.

For adjustment of provision of a door in the cross-section plane of the car at door removals slightly give nuts of fastening of loops to a body, establish a door and adjust its situation. Then remove a door and tighten nuts.

In need of small adjustment of provision of a door up-down and vnut-outside at an open door give a nut, beat out the plug, tighten a nut and adjust the provision of a door.

Internal furnish of doors

The description provided below for a driver's door suits all lateral doors.

PERFORMANCE ORDER

Remove a strip (1) on inside of a frame of a door. On a driver's door separate the socket of the block of adjustment of external mirrors.

Remove the handle (2) unlockings of the lock of a door and the handle of opening of a door (3).
Remove from clamps on door perimeter the panel of its furnish (4) and remove it from the lock button.
Remove from furnish a lamp and separate the socket all sockets (6).
Installation is made upside-down.

Replacement of an external rear-view mirror, its dismantling and assembly

PERFORMANCE ORDER

Remove a strip (1) on inside of a frame of a door and separate the socket (2) mirrors.

Turn out 4 screws of fastening of a mirror (3) and remove it from a door, having pulled back.

Do not drop screws in a door.

For removal of glass of a mirror wring out it a screw-driver from a clamp and disconnect from it heating electroconducting /

For removal э / the motor of adjustment of provision of a mirror remove mirror glass, turn out 3 screws and separate the socket э / the motor.

Assembly and installation of a mirror are made upside-down.

Glass and window regulator

PERFORMANCE ORDER

Remove internal furnish of a door and the vlagozashchitny screen.
At glass removal slightly give screws of fastening of a mirror and remove external consolidation, having turned out the screw on its back part.

Lower glass so that his holder was visible at the top of a big bottom opening (3).

Disconnect window regulator levers from rollers bottom directing, having taken out clips and having hooked levers a wide screw-driver.

Not to bend the lever insert a screw-driver between the lever and directing, is closer to the hinge.

If glass replacement is required, take it from a door outside for back edge.
Fix glass on a frame by means of strips of a sticky tape.

Vypressuyte the central parts of rivets of fastening of a window regulator to a door also drill rivets (6,7).

Separate the socket (8) and turn out two screws (9) of fastening of the directing.
Take a window regulator from a door through a big opening.
Installation is made upside-down. Grease rollers and directing.

External handle and lock

For handle removal previously it is required to remove the lock.

PERFORMANCE ORDER

Lower a window, open a door and remove a strip round a door frame.
Remove internal furnish of a door and the vlagozashchitny screen.
Slightly give screws of fastening of a mirror and remove external consolidation, having turned out the screw on its back part.
Lower glass so that his holder was visible at the top of a big bottom opening (3).
Disconnect window regulator levers from rollers bottom directing, having taken out clips and having hooked levers a wide screw-driver.

Not to bend the lever insert a screw-driver between the lever and directing, is closer to the hinge.

Take glass from a door outside for its back edge.

Vypressuyte the central parts of rivets of fastening of a metal plate also remove from a plate electroconducting (9). Then drill rivets (10), remove a plate and unhook electroconducting from the lock.

Weaken fixture of protection of the lock, having turned out a back nut of the handle and protection and the protection screw.

Weaken fixture (12) bottom edges directing, pull directing forward and remove protection of the lock.

Turn out 3 screws (14) of fastening of the lock to a door and remove from the lock draft (15), turning the lock and at the same time unhooking draft between the lock and the external handle.

Separate the socket (16) and remove the lock (17).

Give a forward nut of fastening of the handle and remove a plate.

Insert a key into the lock, turn it counter-clockwise.
At first delay a back part of the handle on so many that the end of draft entered into a lever flute, and then extend the handle outside as much as possible.

Turn out the screw of fastening of the holder of the cylinder of the lock, turn the holder clockwise (looking from the back party of the handle) and вытолкните it from the handle.

Finally remove the handle and its consolidation. If necessary replace consolidation.
Installation is made upside-down.