Saab 9-5

since 1997 of release

Repair and car operation



Saab 9-5
+ Saab 9-5 Cars
+ Governing bodies and operation receptions
+ Settings and routine maintenance of the car
+ Engine
+ Systems of cooling of the engine, heating, ventilation and air conditioning
+ the Power supply system and production of the fulfilled gases
+ Systems of electric equipment of the engine
+ Manual box of gear shifting
- Automatic transmission
   General information
   Search of malfunctions - the general information
   Removal and installation of assembly of the lever of the selector of AT modes and its casing
   Removal, installation and adjustment of a cable of the selector of AT modes
   Removal and installation of the lever of the selector of AT modes and dismantling of its casing
   Removal and installation Ý/m AT valves, their case and its cover
   Removal and installation of sensors of speed
   Removal and installation of the AT hydraulic lines
   Removal and TCM installation
   Replacement and adjustment of the sensor of position of the selector of AT modes
   Removal and AT installation
   Replacement of epiploons of power shafts
+ Coupling and power shafts
+ Brake system
+ Suspension bracket and steering
+ Body
+ Onboard electric equipment





Removal and AT installation

 PERFORMANCE ORDER

  1. Lay on wings protective covers and remove the top cover of the engine.
  2. Remove the storage battery together with the pallet.
  3. Remove the assembly block of the relay and safety locks and remove it aside. Separate the sockets fixed in holders.
  1. Remove from AT a ventilating hose (6), establish the selector (7) lever on AT in situation "L" and remove it.
  1. Remove a clamp and take a cable of a drive of the lever of the AT selector from an arm (8). On 6-cylinder models disconnect the cable channel (9) from the power unit.
  2. Turn out 3 top bolts (10) fastenings of AT, clear area round a joint of a jellied tube with AT and lift the receiver (11 and 12).
  1. Separate the socket (ы) a lambda probe (ов) (13), give a nut (14) fastenings of a back support of the engine and bolts (15) fastenings of a back pillow of the engine

Bolts completely do not turn out.

  1. Hang out the power unit and lift the car.
  2. Remove forward wheels, the bottom protective casings of an impellent compartment and forward section of final system.
  1. Turn out bolts (22) fastenings of the steering mechanism, remove two back collars (23) fastenings of a submitting tube of GUR to a stretcher and remove tubes To/in from plastic collars on a stretcher.
  1. Remove the case of an air purifier (24). On 4-cylinder models disconnect a radiator from an interkuler (25).
  2. From both parties of the car give bolts of fastening of spherical support of a suspension bracket to rotary fists and bolts of racks of the stabilizer of a suspension bracket (36).
  1. Remove a forward support of the power unit and basic plates (29).
  1. Establish under a stretcher the special stand and give the remained 4 bolts (32) fastenings of a stretcher.
  2. Lower a stretcher at the stand approximately on 5 cm that it was possible to remove two forward collars of fastening of submitting tubes of GUR. Remove collars, lower the stand together with a stretcher and take him aside.
  3. Remove a back support and an engine (34) pillow.
  4. On 4-cylinder models remove the plate fixed by two bolts to get access to hydrotransformer fastening on a driving disk. On 6-cylinder models remove a stopper (under a starter), closing hydrotransformer (35) bolts.
  1. Turn out 6 bolts of fastening of the hydrotransformer to a driving disk, turning for this purpose a cranked shaft (36).
  1. Wring out the hydrotransformer from transmission and fix it in this situation by means of the special adaptation (37) for the period of AT removal.
  2. Remove the components specified an illustrations. Empty AT.
  3. Take from AT the left power shaft, suspend it on a plait and lower the car.
  4. Remove the left pillow of the engine.
  5. Lower the power unit approximately on 10 cm that AT was released from a constructive element. Lift the car.
  6. Fix on a jack the special adaptation, level its center with the AT center and with its interfaced surface (see an illustration).
  1. Turn out the remained bolts of fastening of AT to двигател, separate them and remove AT from the special adaptation.
  1. Installation is made upside-down.